This automatic optical fiber tensile testing system is ideal for operator skill impartial use in production and laboratory settings. Two fundamental model configurations enable the user to pick from a set up for regular linear proof screening along with extra mandrels for rotary higher power testing.

The linear version is ideal for production proof testing with forces as much as 22 N. Motorized clamps with very carefully developed rubber inserts ensure that the Secondary Coating Line will not be damaged inside the screening procedure while concurrently eliminating the requirement for an external atmosphere provide. Degrees of pulling pressure, tugging velocity and keep time are automated and conveniently available to the owner through the built in Liquid crystal display touchscreen display manage. Data from tests could be saved and reached using the USB dock or Ethernet interface.

Mandrels the exact same design as in NYFORS’ optical fiber recoaters could be installed on the proof tester within the rotary higher power configuration. The fiber is covered around the two mandrels which assistance it having a special clamping system. This way much higher lots does apply on the fiber, allowing breaking strength assessments below managed circumstances.

Adjustable clamp positioning facilitates testing with all the greatest pressure amounts along with testing of short fiber measures. The compact and lightweight weight design helps make the instrument easy to maneuver within a lab environment as well as incorporate inside a creation work table in which space are at reduced. The machine is actually a compact and lightweight tool ideal for screening the effectiveness of optical materials up to 30 N. The equipment is designed to meet all kinds of applications when a power test needs to be performed.

The machine was created with all the consumer under consideration. The Yarn Binder is definitely put into the carefully guided linear clamps, as well as the testing begins instantly with a “One Touch” go switch. The built in microprocessor regulates each of the essential parameters including pulling force, tugging velocity and keep time. This permits for any completely controlled test each and every time.

The machine could be linked to an external PC, which enables usage of all programmable guidelines and settings. The equipment is adapted to stand-on your own use or to the integration into various subsystems. The equipment comes with an substantial capability of signing and saving details like pulling force, tugging speed and fiber size along with other parameters.

Two recoat injector configurations can be found. The PTR307 uses a computerized water pump to inject the recoat material. The amount of material dispensed by the automatic injector is controlled by hand using the best-mounted “Inject” button or programmed in to the device using the tablet pc control. The PTR307B features a handbook recoat injection system that requires the user to manually dispense the recoat materials into the mildew cavity; a replacement injector for that PTR307B recoater is accessible below. Please be aware that this automatic injector is just compatible with high-index recoat material, while the handbook injector works with both low- and- directory recoat materials; both of them are marketed individually listed below. Make sure you contact Technology Support for more information.

he handbook injector could be installed to Cable Air Wiper using the 4-40 screws in the recoater real estate (see picture off to the right). Utilize a 3/32″ hex key to safe the injector prior to use. To connect the PTRRRM to the recoater mold, tighten up the connector after the green plastic material tubes, then loosen by a 1/4 choose permit rotation.

The injector comes with a distribution device as well as 2-position selection lever for directing the stream of recoat materials. A knurled dispensing attach having an inner plunger works as a syringe for the recoat materials. To fill the syringe, point the handle downward (i.e., toward the recoat container), then rotate the knurled dispensing screw counterclockwise till it ikrsve easily to fill the syringe (demonstrated in the photo to the right). Then, to inject the recoat material into the mildew, point the lever horizontally (i.e., dealing with the knurled screw) and rotate the screw clockwise until near the finish of the travel array is achieved. Steer clear of bottoming out the dispenser since this may damage the interior plunger; also take care when re-engaging the threads to avoid go across threading the dispensing screw. Several fill/inject steps may be required till atmosphere is displaced in the system. Use lens tissue plus an acetone or alcoholic beverages cleansing solution to gather any excess recoat material that flows through the mold.

Sheathing Line – New Details On This Issue..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.